106" 



GRIFFITH, TURNER & CO., BALTIMORE, MD. 



The Waldron & Sprout Vertical French Burr Mill. 



The Best Burr Stone Mill ever offered to the Trade. The Celebrated Vertical French 

 Burr Mills, Suitable for Grain or any Material that may be Ground in a Mill. 



SPECIAL 12=INCH MILL FOR ANY LIGHT POWER. 



Dimensions.— Extreme length, 36 inche s ; width, 19 

 inches ; height, 34 inches ; base occupies floor space, 17 x 17 

 inches; driving pulley, 8 inches diameter, 5 inches face. 

 Speed, 800 to 1,200 revolutions per minute. The burrs in 

 this mill are each 12 inches in diameter, carefullytested and 

 tried after they are placed in the frame. The runner is at- 

 tached to the spindle by a divided tapered sleeve and nut. 

 The grinding capacity is from 5 to 15 bushels an hour, ac- 

 cording to the fineness required of 

 the meal or feed. It has the end 

 motion silent shoe feed that will 

 feed from 1 quart to 20 bushels an 

 hour, according to the speed of the 

 mill, which adapts it particularly for 

 wind power. 



It is furnished with ball bearings, 

 and the shells are rabbeted, turned 

 and bored the same as the mills of 

 much greater capacity. Every part 

 is made interchangeable, and. can 

 be replaced at a nominal cost. 

 It has only two bearings, runs very light and requires but a very small amount of power to 

 •operate it. It is well and strongly built and is designed for use on a farm, and is just the machine 

 for a farmer to have. 



It is the cheapest mill that has ever been put upon the market, both in point of purchase price 

 :and in comparison with mills of greater capacity that do not contain the especial features and 

 improvements that have brought our mills into popularity and general favor. Weight, 400 pounds. 

 Price, $65 



12-inch Mill. — Dimensions: Length over all, 56 inches; width, 22 inches; height, 31 inches; 

 driving pulley 8 inches in diameter, 5-irich face, covered with leather; weight, 430 pounds ; should 

 be run 1,000 to 1,200 revolutions per minute ; grinding capacity, 5 to 15 bushels per hour, according 

 to fineness of meal or feed and power used ; power required to operate above, 6 to 8 horse-power 

 engine. Price, $100. 



16-inch Mill. — Length over all, 64 inches ; width, 24 inches ; height, 36 inches ; floor space, 22 x 

 45 inches ; driving pulley, 10 inches in diameter, 6-inch face, covered with leather ; weight, 800 

 pounds ; should be run 1 000 revolutions per minute ; grinding capacity 10 to 3o bushels per hour ; 

 power required to run this mill satisfactorily, 8 to 12 horse-power. Price, $160. 



20-inch Mill. — Length over all, 77 inches ; width, 30 inches ; height, 41 inches ; floor space, 24 x 

 54 inches ; driving pulley, 12 inches in diameter, 10-inch face, covered with leather ; weight, 1,200 

 pounds ; should be run 900 revolutions per minute ; grinding capacity, 15 to 60 bushels per hoar; 

 10 to 15 horse-power engine required. Price, $200. 



24-inch Mill. — Lenghth over all, 81 inches ; width, 32 inches ; height, 51 inches ; floor space 

 occupied by base, 27 x 57 inches ; driving pulley 16 inches diameter, 8-inch face, covered with 

 leather ; weight, 1,800 pounds ; should run 800 revolutions per minute ; grinding capacity, 15 to 75 

 bushels per hour, according to fineness of feed and meal required and power used. This mill is 

 adapted to any place where it can have from 15 to 25 horse-power. It has the end motion silent 

 shoe feed, and is filling the pla'ce of the 30 inch in many places, as it will do almost as much work 

 with less power, and is easier to handle. Price, $275. 



30-inch Mill. — Length over all, 78 inches ; width, 39 inches ; height, 55 inches ; floor space, 30 x 

 53 inches ; driving pulley, 20 inches in diameter, 10-inch face, covered with leather; weight, 2,500 

 pounds ; grinding capacity 25 to 100 bushels per hour; should be run 700 revolutions per minute ; 

 power required, 20 to 30 horse-power. Price, $325. 



In addition to above we can furnish a full line of these mills for grinding fish, oil cake, Charles- 

 ton rock, &c, &c. 



IMPROVED CRUSHERS-TWO SIZES. 



No. 1 will crush 20 to 35 bushels of corn on the ear per hour ; weight, 350 pounds ; driving pulley, 

 16 inches diameter, 4-inch face ; should be run 300 to 400 revolutions per minute ; power required, 



2 horse-power. Price, $40. 



No. 2 will crush 60 to 90 bushels of corn on the ear per hour ; weight, 500 pounds ; driving pulley, 

 20 inches diameter, 4-inch face ; should be run 200 to 300 revolutions per minute ; power required, 



3 horse-power. Price, $60. 



It will pay you to write for catalogue and prices before purchasing elsewhere. 

 Elevator attachments to connect mill and crusher, $5. 



ALL KINDS OF MACHINERY REPAIRED. 



