"lima" SELF-FEEn ensilage cutter With Direct Blast Blower Ele»a lof 



As compared with the "Ohio" Standard machines, there Is more weight and capacity all through. 

 The frame is heavier and well braced. The knife shaft is steel, IJi inches in diameter. The knife 

 heads are very mnch heavier, the cylinder largrer in diameter, and there are four strong bolts In each 

 knife in addition to the adjusting set screws at the back. The raise of the feed rolls is greater, thus 

 giving more throat capacity and better feeding qaaiities. The conveyor beneath the knives carries the 

 cut silage into the fan case. A wire screen covers the outer end of the conveyor case. 

 The traveling feed table is full width of the machine and 8 feet long, taking a bundle of corn readily. 

 The new paient-applied-for shredder blade should be run at 600 to 700 revolutions per minute while 

 shredding, and is a notable advance in construction, enabling the operator to shred dry fodder or 

 cornstalks with the blower. There is a great saving In power also as compared with the tooth or saw 

 blade type of shredder, besides saving the leaves Inmuch better condition. No. 14, capacity 

 12 to 15 tons per hour, 10-horse steam power; No. 17, capacity 15 to 20 tons per hour. 10 

 to 12 horse steam power; No. 19, capacity 20 to 25 tons per hour, 12 to 14 horse steam 

 power. Speed, 650 to 700 revolutions per minute. Pulley, 12x8 inches, leather covered. 



SIZES AND PRICES. 

 No. 12, with four 12-inch knives, cuts %, % and 1 inch, and Blower 



complete, with new distributor for too of pipe ....S160.00 



No. 14 "Monarch" Cutter, four 14-inch knives, cuts % and 1 inch, 



and Blower complete with new distributor for top of pipe 185.00 



No. 17 "Monarch" Cutter, four 17-inch knives, cuts li, % and 1 Inch, 



and Blower complete with new distributor for top of pipe 220.00 



No. 19 "Monarch" Cutter, four 19-inch knives, cuts %, % and 1 inch, 



and Blower complete with new distributor for top of pipe 250.00 



10-Inch galvanized pipe in 4, 6, 8 and 10 foot lengths for No. 14, 



No 17 or No. 19 Cutter, per foot JK) 



Extra gears to cut 4 inches long with two knives, Nos. 14, 17, 19. ... (USO 

 Shredder blades for No. 14. S3.50; No. 17, 94^r,t No. 19, «4.S5 each. 



Machines less 30 Per Ct. Knives. Shredder Blades and Extras, net prices. 



Fig. 803. 



oi I <^""er has long been our most popular size 

 it 4% flfrt ^^IZ "if^- " adapted to cutting all kinds 

 Sf,nt '^i! 1 "^^^ ^.^ ensilage, is strongly and durably 

 ^,Vn ^ '^r^® capacity and requires but slight power to 

 •L'"'^'^*^® diameter and is made of 

 galvanized steel with standing seam on the outside run- 

 ?A"fo}f*°f being very rigid. It is made in 4, 6 and 



ilJ^X I'^^r}^-^ ■V^^r^l-''"'-^ sl'P joints and a clamping 

 owi,^^'^^^ rJ\^ P'Pe connection at the fan case 



Is a swivel joint, which gives the pipe the proper angle 

 for convenience and best results, and allows it to turn in 

 any direction. Included with each machine Is a hood or 

 fl J'Zi^Il^nJ^ *° connect to upper end of pipe and convey 

 the cut ensilage into the silo. 



Set Pipe Nearly Perpendicniar for Ensilage. Dry Peed 

 Can Be Blo\^-n in Any Direction. 



wS- }}~^}}}}}"^° i^"'"- ^n'.ves, cuts %, 1 and 2 in...?95.00 



No. 11 — With two shredder blades, no knives 96.50 



No. 11 — With four shredder blades, no knives 103.00 



Above prices are for machines complete with Blower 

 and Hood, but no pipe. 



7-in. galvanized pipe in 4, 6 and 10-ft. lengths, per ft..S .60 



Extra gears to cut 4 Inches long with two knives 3J50 



Cutting knives, each 150 



Shredder blades, interchangeable with knives! each ! ! 2.25 

 Note—Where not more than the minimum power — 4 

 norse — is available, we recommend the use of the two- 

 knife machine. Machines less 30 Per Ct. Knives, Shredder 

 Blades and Extra.s, net prices. 



NEW STEEL TRUCK 



FOR MOUNTING "OHIO" ENSILAGE CTITTERS. 



The frame is of steel throughout. The axleo and 

 reach are made of 3-inch steel channels, the axli 

 channels being firmly bolted face to face over a wool 

 core. Distance between front and rear axles is 8 feet 

 4 inches. The wheel tread is 5 feet 2 Inches The 

 cast Iron wheels, 24 inches in diameter, are built tS 

 wear. The frame is securely put together. When 

 mounted complete the machine is but 12 inches from 

 the ground and the top of feed table 45 inches from 

 ground. By sinking the wheels or removing them 

 the axles may be let down on to the ground, in which 

 case the machine would be but 3 incites from ground 

 the thickness of the steel reach. The highest ooint 



ground, thus no staging or platform would be re- 

 quired to get corn to the machine. 



This outfit Is suitable for all sizes of "Ohio" silage 

 cutters with traveling feed tables, both blower and 

 carrier styles, and is recommended as 

 a thoroughly practical, economical and 

 satisfactory mounting for all parties 

 who wish to move their machines fre- 

 quently or regularly. All parts are In- 

 terchangeable, and in case of accident 

 may be readily replaced. 



Price of Truck, without neck yoke or double trees, welghi 600 



lbs., (50.00. Less 30 per cent, retail. 



ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE. 



