^ GRIFFITH ®, TURNER CO, ^ »23 



"OHIO" SELF-FEED ENSILAGE CUnER With Direct Blast Blower El^r 



As compared with the "Ohio" Standard machines, there is more weight and capacity all through. 

 The frame is heavier and well braced. The knife shaft is steel, IJi inches in diameter. Tlie knife 

 heads are very much heavier, the cylinder larger In diameter, and there are four strong bolts in each 

 knife In addition to the adjusting; set screns at the back. The raise of the feed rolls is erreater, thus 

 Sivlns more throat capacity and better feeding qualities. The conveyor beneatli the knives carries the 

 cut silage into the fan case. A wire screen covers the outer end of the conveyor case. 



The traveling feed table is full width of the machine and 8 feet long, taking a bundle of corn readily. 

 The new patent-applied-f or shredder blade should be run at 600 to 700 revolutions per minute while 

 shredding, and is a notable advance in construction, enabling the operator to shred dry fodder or 

 cornstalks with the blower. There is a great saving in power also as compared with the tooth or saw 

 blade type of shredder, besides saving the leaves inmuch better condition. No. 14, capacity 

 12 to 15 tons per hour, 10-horse steam power; No. 17, capacity 15 to 20 tons per hour, 10 

 to 12 horse steam power; No. 19, capacity 20 to 25 tons per hour, 12 to 14 horse steam 

 power. Speed, 650 to 700 revolutions per minute. Pulley, 12x8 inches, leather covered. 



SIZES A.\D PRICES. 

 No. 12, with four 12-inch knives, cuts and 1 inch, weight 1,425 



pounds $160.00 



No. 14 "Monarch" Cutter, four 14-inch knives, cuts % and 1 inch, 



and Blower complete with new distributor for top of pipe 186.00 



No. 17 "Monarch" Cutter, four 17-inch knives, cuts % and 1 Inch, 



and Blower complete with new distributor for top of pipe 220.00 



No. 19 "Monarch" Cutter, four 19-inch knives, cuts % and 1 inch, 



and Blower complete with new distributor for top of pipe 250.00 



10-inch galvanized pipe in 4, 6, 8 and 10 foot lengths for No. 14, 



No. 17 or No. 19 Cutter, per foot 90 



Extra gears to cut 4 inches long with two knives. Nos. 14, 17, 19. . . . 6.50 

 Shredder blades for No. 14, «3.50; No. 17, $4.25; Xo. 19, $4.85 each. 



Less 30 Per Cent. Retail. 



Fig. 802. 



The No. 11 Cutter has long been our most popular size 

 for general farm use. It is adapted to cutting all kinds 

 ^^^^ ensilage, is strongly and durably 

 bunt, has large capacity and requires but slight power to 

 run. ihe pipe IS / inches in diameter and is made of 

 galvanized steel with standing seam on the outside run- 

 ning lengthwise, being very rigid. It is made in 4, 6 and 

 10 foot lengths with <-inch slip joints and a clamping 

 band at each joint. The pipe connection at the fan case 

 Is a swivel joint, which gives the pipe the proper angle 

 for convenience and best results, and allows it to turn in 

 any direction. Included with each machine is a hood or 

 elbow which is to connect to upper end of pipe and convey 

 the cut ensilage into the silo. 



Set Pipe Nearly Perpendicular for Ensilage. Dry Peed 



Can Be Blown in Any Direction. 

 Jjo- 3.'*? 11-in. knives, cuts V2, 1 and 2 in... $95.00 

 W — 11-in. knives, cuts ^ and 1 in.. 100.00 



No- 11 — With two shredder blades, no knives 96.50 



No. 11 — "With four shredder blades, no knives 103.00 



Above prices are for machines complete with Blower 

 and Hood, but no pipe. 



7-in. galvanized pipe in 4, 6 and 10-ft. lengths, per ft. .$ .60 



Extra gears to cut 4 Inches long with two knives 3.50 



Cutting knives, each I.50 



Shredder blades, interchangeable with knives, each.. 2.25 

 Note-pWhere not more than the minimum power — 4 

 liorse — is available, we recommend the use of the two- 

 knife machine. 



Less 30 Per Cent. Retail. 



NEW STEEL TRUCK 



FOR MOLNTIXG "OHIO" ENSILAGE3 CUTTERS. 



The frame is of steel throughout. The axles and 

 reach are made of 3-inch steel channels, the axle 

 channels being Hrmly bolted face to face over a wood 

 core. Distance between front and rear axles is 8 feet 

 4 inches. The wheel tread is 5 feet 2 inches. The 

 cast iron wheels, 24 inches in diameter, are built to 

 wear. The frame is securely put together. When 

 mounted complete the machine is but 12 inches from 

 the ground and the top of feed table 45 inches from 

 ground. By sinking the wheels or removing them 

 the axles may be let down on to the ground, in which 

 case the machine would be but 3 inches from ground 

 tlie thickness of the steel reach. The highest point 

 of feed table would then be only 36 inches from 

 ground, thus no staging or platform would be re- 

 quired to get corn to the machine. 



This outfit is suitable for all sizes of "Ohio" silaee 

 cutters with traveling feed tables, both blower and 

 carrier styles, and is recommended as 

 a thoroughly practical, economical and 

 satisfactory mounting for all parties 

 who wish to move their machines fre- 

 quently or regularly. All parts are in- 

 terchangeable, and in case of accident 

 may be readily replaced. 



Price of Truck, without neck yoke or double trees, weight 600 

 lbs., $50.00. Less 30 per cent, retail. 



ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE. 



